| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
90℃
|
Non-Immersed
160℃
|
||
| Product type | Medium viscosity Bisphenol ‘A’ polyester glass flake. | Recommended DFT | ||
| Description | Used for coating intricate components by brush, requiring ease of application and contour following i.e. pump impellers. | 0.5 to 1.5 mm in multiple coats | ||
| Surcface preparation | The surface to be coated should be free from grease etc. Metal should be grit blasted to ISO Standard 8501-1 Sa 2½ or equivalent, with a surface profile of at least 75 microns, 100-125 microns being the ideal key. | SDS | ||
Use applications
Coating method
＊There are more coating materials but we listed de most common use.
Pump repair & refurbishment
Corroglass 202
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
90℃
|
Non-Immersed
160℃
|
||
| Product type | High build glass flake coating based on Bisphenol ‘A’ polyester resin. | Recommended DFT | ||
| Description | Developed for applications where good corrosion, abrasion and chemical resistance is required. Ideal for small areas/components with either metal or masonry substrates in arduous conditions. | 1 to 3 mm in two coats or as advised, may be built up to any desired thickness for repair via multiple coats. | ||
| Surcface preparation | The surface to be coated should be free from grease etc. Metal should be grit blasted to ISO Standard 8501-1 Sa 2½ or equivalent, with a surface profile of at least 75 microns, 100-125 microns being the ideal key. | SDS | ||
POLYGLASS VE VEILCOAT
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
110℃
|
Non-Immersed
185℃
|
||
| Product type | A wax inhibited vinyl ester/acrylic surface veil coating. | Recommended DFT | ||
| Description | For use as a waxed surface veil to Polyglass materials where surface inhibition must be avoided. | 200-400 microns | ||
| Surcface preparation | Metals: Gritblast to ISO standard 8501-1 SA 2 near 3 or equivalent. (For full details refer to Corrocoat Surface Preparation SP1). | SDS | ||
POLYGLASS VEHA
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
110℃
|
Non-Immersed
185℃
|
||
| Product type | Vinyl ester acrylic co-polymer enhanced with glass flake for hand application. | Recommended DFT | ||
| Description | For small areas of application where spraying is impractical and for stripe coating spray grades of Polyglass. | When used alone two or more coats of Polyglass VEHAuntil a minimum DFT of 650 microns, over thickness is not detrimental. When used as a stripe coat a single layer of circa 300um, or as otherwise specified. |
||
| Surcface preparation | For optimum performance of these products under immersed conditions,grit blast steel to ISO standard 8501-1 Sa 2½ near 3 or equivalent, prior to application. For full details refer to Corrocoat Surface Preparation SP1 | SDS | ||
POLYGLASS VE
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
110℃
|
Non-Immersed
185℃
|
||
| Product type | Vinyl ester/acrylic co-polymer enhanced with glass flake. | Recommended DFT | ||
| Description | Ideal for hydrocarbons, aggressive chemical environments and environment demineralised water. A chemical resistant floor and concrete coating. | 500 to 3000 microns dependent upon service environment | ||
| Surcface preparation | Metals: Grit blast to ISO standard 8501-1 Sa 2½ near 3 or equivalent. (For full details refer to Corrocoat Surface Preparation SP1.) Concrete: Refer to Corrocoat SP5. | SDS | ||