| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
－
|
Non-Immersed
－
|
||
| Product type | A peroxide catalysed, glass flake polyester primer | Recommended DFT | ||
| Description | As a primer for concrete surfaces that are damp, or were levels of moistures are approching the saturation poit of concrete | DFT is not specified. Wet film thickness should be checked and be within the range 100 to 150 microns during application. | ||
| Surcface preparation | Mechanical abrasion of the surface is required to provide a physical “key” for the product to adhere to, prepare the surface of the concrete. Refer to data sheet SP5. | SDS | ||
Use applications
Coating method
＊There are more coating materials but we listed de most common use.
POLYGLASS
POLYGLASS ZIP COAT
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
50℃
|
Non-Immersed
90℃
|
||
| Product type | A rapid cure polyester acrylic glass flake developed for single coat application | Recommended DFT | ||
| Description | This product is suitable for structural steel, superstructures and other nonimmersed surfaces as well as aqueous and marine immersion at increased thicknesses. | 500 microns non immersed, 800 microns minimum in immersion. |
||
| Surcface preparation | Metals: Grit blast to ISO 8501-1 Sa 2 or equivalent standard. (For full details refer to Corrocoat Surface Preparation SP1). Concrete: Priming is required. See Corrocoat Surface Preparation Specification SP5. | SDS | ||
POLYGLASS 100
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
60℃
|
Non-Immersed
80℃
|
||
| Product type | Two-pack isophthalic polyester acrylic glass flake coating. | Recommended DFT | ||
| Description | Developed for marine, crude oil, limited chemical and heavy duty atmospheric applications | A single or two coat application directly to steel, generally at 600um DFT for atmospheric or 850um and above for immersion conditions. PPA primer may be required for logistical purposes. |
||
| Surcface preparation | Metals: Grit blast to ISO standard 8501-1 Sa 2 or equivalent. Concrete: refer to Corrocoat data sheet SP5. | SDS | ||
POLYGLASS VE VEILCOAT
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
110℃
|
Non-Immersed
185℃
|
||
| Product type | A wax inhibited vinyl ester/acrylic surface veil coating. | Recommended DFT | ||
| Description | For use as a waxed surface veil to Polyglass materials where surface inhibition must be avoided. | 200-400 microns | ||
| Surcface preparation | Metals: Gritblast to ISO standard 8501-1 SA 2 near 3 or equivalent. (For full details refer to Corrocoat Surface Preparation SP1). | SDS | ||
POLYGLASS VEPG
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
110℃
|
Non-Immersed
175℃
|
||
| Product type | A two-pack cold cured vinyl ester/acrylic co-polymer enhanced with flaked glass, specifically formulated to be applied using pipe rolling rig. | Recommended DFT | ||
| Description | Immersed environments where superior resistance to chemical attack is required, VE is suitable for most chemical environments within the pH range of 0 to 13. | Between 750 and 3000 microns dependent upon environment. | ||
| Surcface preparation | Metals: Grit blast to ISO 8501-1 Sa 2½ near 3 or equivalent. For full details refer to Corrocoat Surface Specification SP1. Concrete: Grit blast to remove surface laitance. See Corrocoat Surface Specification SP5. | SDS | ||
POLYGLASS VEHA
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
110℃
|
Non-Immersed
185℃
|
||
| Product type | Vinyl ester acrylic co-polymer enhanced with glass flake for hand application. | Recommended DFT | ||
| Description | For small areas of application where spraying is impractical and for stripe coating spray grades of Polyglass. | When used alone two or more coats of Polyglass VEHAuntil a minimum DFT of 650 microns, over thickness is not detrimental. When used as a stripe coat a single layer of circa 300um, or as otherwise specified. |
||
| Surcface preparation | For optimum performance of these products under immersed conditions,grit blast steel to ISO standard 8501-1 Sa 2½ near 3 or equivalent, prior to application. For full details refer to Corrocoat Surface Preparation SP1 | SDS | ||
POLYGLASS VEF
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
110℃
|
Non-Immersed
185℃
|
||
| Product type | Vinyl ester/acrylic co-polymer loaded with glass flake and thixotroped with fibre. Spray application only. | Recommended DFT | ||
| Description | May be used in identical conditions to Polyglass VE, offering superior. corrosion, chemical and temperature resistance. |
500 to 3000 microns dependent upon service environment. | ||
| Surcface preparation | Metals: Grit blast to ISO standard 8501-1 Sa 2½ near 3 or equivalent. (For full details refer to Corrocoat Surface Preparation SP1.) Concrete: refer to Corrocoat SP5. | SDS | ||
POLYGLASS VE
| Product information | Coating method | Temperature limit | ||
|---|---|---|---|---|
| Application |
Immersed
110℃
|
Non-Immersed
185℃
|
||
| Product type | Vinyl ester/acrylic co-polymer enhanced with glass flake. | Recommended DFT | ||
| Description | Ideal for hydrocarbons, aggressive chemical environments and environment demineralised water. A chemical resistant floor and concrete coating. | 500 to 3000 microns dependent upon service environment | ||
| Surcface preparation | Metals: Grit blast to ISO standard 8501-1 Sa 2½ near 3 or equivalent. (For full details refer to Corrocoat Surface Preparation SP1.) Concrete: Refer to Corrocoat SP5. | SDS | ||